ULTRA-AIR SEPTIC TANK SHAFT AERATOR with 12" Brackets

Description

ULTRA-AIR MODEL
7
35 Septic Aerator With
Red
12" Brackets
FREE SHIPPING!
The Ultra-Air™ Model 735 Red is a compatible alternative replacement septic tank shaft aerator for the Jet systems*. The 735 Red model has 12'' top brackets that are designed to fit a 10'' diameter opening.
ULTRA-AIR Model 735 Aerator Features:
1/4
HP, 115V, 60HZ, 1725 RPM
4.
6 FLA, 3.5 A Operating Current
Aerodyna
mic Plastic Asp
irator
Balanced 5/8" Stainless Steel Shaft
Brass Coupling with Set Screws
Large Plastic Su
ds Restrictor
Pow
der Coated Stee
l Brackets
Rubber Vibration Control Feet
Plastic Moto
r Guard with Handle
Runs on 4 amp or 7
amp Current
Works wi
th Existing Control
Panels
De
signed for Co
ntinuous Operation
Includes Pow
er Cord with Plug
12" Brackets Fit 10" O
pening
Not Test
ed or Approved by NSF
Made in the USA
R
eplacement
Parts A
vailable
1 Year Warranty
This listing is for the Ultra Air Model 735 Aerator with 12" Brackets.  Please see our other listing if you need the larger
14"
Brackets.
The Ultra-Air is not supplied, manufactured, or affiliated with any Certified Aerobic Treatment Manufacturers.
Questions?  Call us toll fre
e at 1-877-925-5132 or
send us an email!
This item is shipped via FEDEX Ground and is fully insured and tracked!
FREE SHIPPIN
G within the contiguous US!
Most orders placed by 2:00pm CST will be shipped same day!
Manufacturer’s recommendations and important information:
It is highly recommended that the
ULTRA-AIR MODEL 735
septic aerator be allowed to run continuously to provide optimum performance and ensure an adequate oxygen supply is readily available inside the septic tank to proliferate the growth of aerobic bacteria. Do not shut off the motor for extended periods of time if left inside the septic tank.
The
ULTRA-AIR MODEL 735
aerator comes with a pre-wired 115-volt plug that is designed to plug into a normal electrical socket or for reference an extension cord. The motor draws only 3.5 amps when operating. When mounted into a tank the motor and the suds restrictor must remain above the highest liquid levels inside the tank. At least every 6 months all motors with a shaft inside the tank should be taken out and any debris on the shaft removed. The stainless steel shaft is hollow and attaches to another hollow shaft that extends through the center of the motor. Air is drawn from the vent on top of the tank lid and down through th
e hollow shafts where it is distributed throughout the tank as defined in the tank illustration. At least once per year the inside of these shafts should be checked to ensure there are no restrictions. Cleaning inside the shaft can be accomplished by using a gun cleaning rod and brush or some other similar means.
Although the
ULTRA-AIR MODEL 735
aerator has been constructed with Permanently lubricated bearings in a fully enclosed housing, it was not designed to be placed in an area that will flood. Only special flood proof motors will handle flooding conditions. A flooded motor will not be covered by warranty.
Warranty is valid in the U.S. only.
Special Note:
Septic Solutions,' Inc.Online Store contains products that are purchased wholesale and then offered for sale. Under no circumstances is Septic Solutions, Inc. representing to the general public that it is an Authorized Distributor or Dealer for those Companies whose products we sell. Although the Ultra-Air Model 735 is similar in design and functionality to products sold by other Manufacturers of NSF Certified products, Septic Solutions, Inc. is not affiliated with, nor claims to be an authorized Distributor for those manufacturers or those complete aerobic systems with NSF Certification containing similar components to the Ultra-Air Model
7
35.
*
Jet is a Registered Trademark of Jet, Inc.